- Home
- Catalog
- Flame SFX
- Gas Flame SFX
- Hansol Cauldron flame, ∅ 40 cm
Hansol Cauldron flame, ∅ 40 cm
Brand: Hansol
- Inspected and tested before every rental
- Comes with its documentation: manual and certificates
- Shipped from our 12,000 m³ warehouse in Affligem, Belgium
- Reachable outside office hours too
Complete your setup?
These items are linked to the Hansol Cauldron flame, ∅ 40 cm. Tick what you need.
Description
The Cauldron Flame System is a perfect substitute for the Olympic Flame Demagnification. It can make propane flame burn up to 1 m high. It runs for about 4 hours for a continuous flame effect. The Cauldron Flame System is designed for use at outdoor events, hotel entrances, casinos or eye-catching parties.
For safety reasons, this system has a safeguard system which is composed of a flame sensing rod and its flame sensing board. Without the solid pilot flame, the effect valve does not open and accordingly, it cannot make the flame burn. The pilot flame strike process repeats until the pilot flame becomes solid and even during the show, when the pilot flame is gone unexpectedly, the pilot re-strike resumes automatically and immediately within 0.3 seconds. When the pilot flame becomes solid, the main valve opens to go in standby state to shoot the flames. During the re-strike process, the main valve stays closed in order to exclude the danger to shoot the flame accidentally. The 1st CH is for the main flame and the CH100 is for the pilot flame.
Technical data
| Dimensions (L × W × H) | 41 × 41 × 37 cm |
|---|---|
| Weight | 12.1 kg |
| Power | 70 W |
| Runs on | Propane |
| Fuel | LP Gas / Propane |
| Mains frequency | 50–60 Hz |
| Power connector | Powercon |
| DMX channels | 2 |
| DMX protocol | DMX 512 |
| Outdoor use | Yes |
| Ignition | HV spark (electronic) |
| LPG consumption | 13.2 kg/h |
| Article code | VH-CR-110 |
Show all specifications (15 more)
| Gas pressure working | 0.3 – 0.5 bar |
|---|---|
| Max. gas pressure | 1 bar |
| Run time continuous | 4 h |
| DMX ch1 function | Main Flame |
| DMX ch2 function | Pilot Flame |
| DMX address setting | DIP switch (8-bit binary) |
| Flame sensor | Yes |
| Pilot flame restrike time | 0.3 s |
| Pilot flames count | 5 |
| Ceramic insulation bottom | Yes |
| Signal connector | XLR 3-pin |
| Optional accessories | Propane hose, propane gas regulator, DMX cable, Powercon mains power cable |
| Handy DMX controller included | No |
| Indoor use ventilated | Yes |
| Voltage | 220 V |
Downloads
New to dry hire? Read how dry hire works.
Accessories
Linked to this item in our system
About flame effects
How it works
Flame units produce real fire on cue, from a short burst to a column of several metres. Gas units burn propane or a propane/butane mix from cartridges or cylinders. Liquid units atomise a flame fluid and ignite it, which gives a flame with more body; some can add colour.
What you need
Fuel: gas cartridges, or a gas cylinder with regulator and hose, or flame fluid. The nozzle sets the size of the flame. Fuels and colour additives are in consumables; hoses, regulators and nozzles are in the accessories of each unit. Not sure whether gas or liquid suits your show? Read liquid vs gas flame: how to choose.
Safety
Every unit has its own safety distances and an indoor or outdoor rating; respect what the product sheet and the manual say. Keep an extinguisher at hand, watch the wind outdoors, and use a safety arm system so that no effect can fire by accident.
Frequently asked questions
Can flame effects be used indoors?
Some units can, in large venues and with the approval of the venue and the fire service; others are for outdoor use only. Check the rating on the product sheet.
More in Gas Flame SFX
View all →
Explo Fire bowl plus, 230V, Ø 60 cm
Explo Fire bowl plus, 230V, Ø 90 cm
Explo GX2, 230 V, excl. hose
Explo SFX Torch
Explo X2 Power Flame, liquid propane flame effect
Hansol Power Flame 1, (max. 6 m)
Hansol Power Flame 2, (max. 10 m)
